Fermentation

The Brew Cooler is a waterproof, insulated cooling bag to keep correct fermentation temperature in fermenters up to 30L. Perfect if you dont have space or possibility to place your fermenter in a temperature controlled refrigerator at home.How the Brew Cooler worksThe function is simple, place your fermenter inside the Brew Cooler and add frozen water bottles (preferrably plastic) inside the Brew Cooler to reduce and keep the correct fermentation temperature. The volume of frozen water in the plastic bottles determines how many degrees below room temperature the fermenter will be kept at. The frozen water bottles should preferrably be replaced every 24 hours, or when needed.1. Place the Brew Cooler at a suitable location in your home. Place your fermenter with wort inside the Brew Cooler.2. Place the correct number of frozen water bottles inside the Brew Cooler according to the Temperature Chart below.3. Close Brew Cooler zip locks.4. After 24 hours, exchange the frozen water bottles for new ones.Temperature Chart: Choose the correct fermentation temperatureThis chart gives examples of the number and size of frozen water bottles that is needed for a given temperature reduction in the Brew Cooler for 20L beer.One 1-liter bottle reduce 1,5°C.Two 1-liter bottles reduce 3°C.One 1,5-liter bottle reduce 2°C.Two 1,5-liter bottles reduce 4°C.Three 1,5-liter bottles reduce 6°CFour 1,5-liter bottles reduce 8°C.One 2-liter bottle reduce 3°C.Two 2-liter bottles reduce 6°C.Three 2-liters bottles reduce 9°C.Four 2-liter bottles reduce 12°C.These temperature reductions are valid for 20L beer in the fermenter. As can be seen, the temperature reduction is about 1,5°C per liter frozen water. The maximum temperature reduction that can be archieved is about 15°C.Example: If your home ambient temperature is 21°C and you want to ferment 20L ale at 18°C, add one 2-liter or two 1L) frozen plastic water bottle together with your fermenter in the Brew Cooler. Exchange every 24 hours and repeat at least the first 3-4 days during the primary fermentation. If your brew 10L then about half the volume, 1-1.5L frozen water, is enough. What is the correct fermentation temperature?To get your home brew to taste as good as possible its important to control the fermentation temperature. An ale can theoretically be fermented at room temperature, 20-22°C, however it will taste the cleanest when fermented around 18°C, at least the first 3-4 days of fermentation. Lagers should be fermented at 10-12°C. Saisons can be fermented at high temperatures, 20-35°C, depending on the flavour profile you want.Brew Cooler 30L specificationsHeight: 60 cmLength 40 cmWidth: 40 cmMaterial: Tough black polyester Kraftig svart polyester with insulation and a grey water proof inner liner.Carrying strap: The Brew Cooler is equipped with an adjustable carrying strap.

The Brew Cooler XL is an extra large waterproof, insulated cooling bag to keep correct fermentation temperature in fermenters and kegs up to 30L. Either one 30L fermenter or two cornelius kegs fits inside. Perfect if you dont have space or possibility to place your fermenter in a temperature controlled refrigerator at home.How the Brew Cooler XL worksThe function is simple, place your fermenter or keg(s) inside the Brew Cooler and add frozen water bottles (preferrably plastic) inside the Brew Cooler to reduce and keep the correct fermentation temperature. The volume of frozen water in the plastic bottles determines how many degrees below room temperature the fermenter will be kept at. The frozen water bottles should preferrably be replaced every 24 hours, or when needed.1. Place the Brew Cooler at a suitable location in your home. Place your fermenter with wort inside the Brew Cooler.2. Place the correct number of frozen water bottles inside the Brew Cooler according to the Temperature Chart below.3. Close Brew Cooler zip locks.4. After 24 hours, exchange the frozen water bottles for new ones.Temperature Chart: Choose the correct fermentation temperatureThis chart gives examples of the number and size of frozen water bottles that is needed for a given temperature reduction in the Brew Cooler for 20L beer.One 1-liter bottle reduce 1,5°C.Two 1-liter bottles reduce 3°C.One 1,5-liter bottle reduce 2°C.Two 1,5-liter bottles reduce 4°C.Three 1,5-liter bottles reduce 6°CFour 1,5-liter bottles reduce 8°C.One 2-liter bottle reduce 3°C.Two 2-liter bottles reduce 6°C.Three 2-liters bottles reduce 9°C.Four 2-liter bottles reduce 12°C.These temperature reductions are valid for 20L beer in the fermenter. As can be seen, the temperature reduction is about 1,5°C per liter frozen water. The maximum temperature reduction that can be archieved is about 15°C.Example: If your home ambient temperature is 21°C and you want to ferment 20L ale at 18°C, add one 2-liter or two 1L) frozen plastic water bottle together with your fermenter in the Brew Cooler. Exchange every 24 hours and repeat at least the first 3-4 days during the primary fermentation. If your brew 10L then about half the volume, 1-1.5L frozen water, is enough. What is the correct fermentation temperature?To get your home brew to taste as good as possible its important to control the fermentation temperature. An ale can theoretically be fermented at room temperature, 20-22°C, however it will taste the cleanest when fermented around 18°C, at least the first 3-4 days of fermentation. Lagers should be fermented at 10-12°C. Saisons can be fermented at high temperatures, 20-35°C, depending on the flavour profile you want.Brew Cooler XL 30L specificationsHeight: 70 cmLength 40 cmWidth: 40 cmInternal supports: 60cm Vertical rib supports keeps the bag upright by itself.Material: Tough black polyester with insulation and a grey water proof inner liner.Carrying strap: The Brew Cooler is equipped with an adjustable carrying strap.Note: Fermenters, kegs or other accessories are not included.

Ferment your beer in stainless conical fermeters just like in professional breweries. Rotary racking arm with dip tube provides very good extraction of beer from above the cone. Perfect for batch sizes up to 30L, optimally 20-25L.Brewly CF 30L Conical Fermenter- Material: Polished stainless steel (ANSI 304)- Polished seamless inside for maximum sanitary conditions- 30L capacity (32L to edge)- Thermometer 0-40C (32-104C) with internal thermowell for the sensor.- Mini valve 3/8" with rotary racking arm with dip tube provides very good extraction of beer from above the cone for bottling or transfer to keg.- Dump valve on conical bottom with 1/2" stainless steel valve, perfect for yeast dumping and easy cleaning.- Internal volume scale up to 30L- 2 steady stainless steel handles- 3 adjustable legs with rubber feet- Airlock with rubber plug- Stainless lid with lock med heavy-duty silicone seal- Diameter: 33,5cm- Height without airlock: 59 cm, adjustable up to 66cm- Height with airlock: 69 cm, adjustable up to76cm- Multiple fermenters can be stacked on top of eachother- Instructions manual in English

Ferment your beer in stainless conical fermeters just like in professional breweries. Built-in stainless cooling spiral chiller with gardena-type connectors for easy connections to a cooling medium of your choice. Build-in thermowell for external temperature sensor probe, for example from a thermostat controlling a pump. Rotary racking arm with dip tube provides very good extraction of beer from above the cone. Perfect for batch sizes up to 30L, optimally 20-25L.Brewly CCF 30L Conical Cooling Fermenter with Chiller- Material: Polished stainless steel (ANSI 304)- Polished seamless inside for maximum sanitary conditions- 30L capacity (32L to edge)- 4,7m built-in stainless cooling spiral chiller with gardena-type connectors for easy connections to a cooling medium of your choice.- 30cm stainless thermowell for external temperature sensor probe, for example from a thermostat controlling a pump (like Brewly AC-211/TC-320 universal thermostats).- Thermometer 0-40C (32-104C) with internal thermowell for the sensor.- Mini valve 3/8" provides very good extraction of beer from above the cone for bottling or transfer to keg.- Dump valve on conical bottom with 1/2" stainless steel valve, perfect for yeast dumping and easy cleaning.- Internal volume scale up to 30L- 2 steady stainless steel handles- 3 adjustable legs with rubber feet- Airlock with rubber plug- Stainless lid with lock med heavy-duty silicone seal- Diameter: 33,5cm- Height without airlock: 59 cm, adjustable up to 66cm- Height with airlock: 69 cm, adjustable up to76cm- Multiple fermenters can be stacked on top of eachother- Instructions manual in English

Ferment your beer in stainless conical fermeters just like in professional breweries. Rotary racking arm with dip tube provides very good extraction of beer from above the cone. Perfect for batch sizes up to 60L, optimally 20-55L.Brewly 60L Conical Fermenter- Material: Polished stainless steel (ANSI 304)- Polished seamless inside for maximum sanitary conditions- 60L capacity (62L to edge)- Thermometer 0-40C (32-104C) with internal thermowell for the sensor.- Mini valve 3/8" with rotary racking arm with dip tube provides very good extraction of beer from above the cone for bottling or transfer to keg.- Dump valve on conical bottom with 3/4" stainless steel valve, perfect for yeast dumping and easy cleaning.- 2 steady stainless steel handles- 3 legs with rubber feet- Airlock with rubber plug- Stainless lid with lock med heavy-duty silicone seal- Diameter: 47 cm- Height: 70 cm- Multiple fermenters can be stacked on top of eachother- Instructions manual in English

Ferment your beer in stainless conical fermeters just like in professional breweries. Built-in 13-meter stainless cooling spiral chiller with gardena-type connectors for easy connections to a cooling medium of your choice. Build-in thermowell for external temperature sensor probe, for example from a thermostat controlling a pump. Rotary racking arm with dip tube provides very good extraction of beer from above the cone. Perfect for batch sizes up to 60L, optimally 25-55L.Brewly 60L Conical Cooling Fermenter with Chiller- Material: Polished stainless steel (ANSI 304)- Polished seamless inside for maximum sanitary conditions- 60L capacity (62L to edge)- 13-meter built-in stainless cooling spiral chiller with gardena-type connectors for easy connections to a cooling medium of your choice.- 30cm stainless thermowell for external temperature sensor probe, for example from a thermostat controlling a pump (like Brewly AC-211/TC-320 universal thermostats).- Thermometer 0-40C (32-104C) with internal thermowell for the sensor.- Mini valve 3/8" with rotary racking arm with dip tube provides very good extraction of beer from above the cone for bottling or transfer to keg.- Dump valve on conical bottom with 3/4" stainless steel valve, perfect for yeast dumping and easy cleaning.- 2 steady stainless steel handles- 3 legs with rubber feet- Airlock with rubber plug- Stainless lid with lock med heavy-duty silicone seal- Diameter: 47 cm- Height: 70 cm- Multiple fermenters can be stacked on top of eachother- Instructions manual in English

Insulation jacket for the Brewly 30L Conical Fermenter (both versions). Material: 5 mm neoprene foam.

The heat pad ensures constant brewing temperature which is crucial for the success of brewing beer, wine or spirits. To be placed under the fermenter. Suitable for fermentation in cold areas such as in a refrigerator or in the basement, garages or on the balcony. Provides a low constant heat to the fermenter which aids yeast activity and helps avoid stuck fermentations.Use preferrably in cojunction with an Universal Thermostat (not included).Features:- Inexpensive to run. - Voltage: 220-240V EU-version power cord (UK power cord NOT included).- Power: 25W- Width: 32 cm- Length: 32 cm

Fermenter made of food grade plastic. Lid and rubber seal for air lock are included. Graded to 12L, 15L maximum.MeansurementsHeight: 32 cmDiameter: 30 cmNote: Fermenter air lock is not included.

Fermenter 15L with lid and tap hole

Fermenter 15L with lid and tap

Plastic lid for 15L fermenter with rubber grommet. Diameter ca 28,5cm

Plastic Fermenter 30L with Lid, Rubber Grommet and Volume Scale

Plastic Fermenter 3-PACK EMB 30L (Lid, Rubber Grommet & Scale)

Fermenter made of food grade plastic. Lid and rubber seal for air lock are included. Graded to 25L, 30L maximum.MeansurementsHeight: 44 cmDiameter: 37 cmNote: Fermenter air lock is not included.

Fermenter made of food grade plastic. Lid and rubber seal for air lock are included. Graded to 25L, 30L maximum.MeansurementsHeight: 44 cmDiameter: 37 cmNote: Fermenter air lock is not included.

Fermenter 30L with tap-hole and lid

Three Fermenters 30L with tap-hole and lid

Fermenter 30L with tap and lidHeight: 44cmDiameter: 37cm

Three Fermenter buckets 30L with tap and lidHeight: 44cmDiameter: 37cm

Plastic lid for 30L fermenter with rubber bussing. ca 36cm diameter.

Steel handle for 30L Fermenter. (Fermenter not included)

3-piece airlock in transparent plastic that fits ordinary plastic fermenters as well as FermZilla and Brewly fermenters. Easy to clean. Fits 9mm holes.

Better Brew Airlock 3 bubbles, fits in standard grommets for standard fermenter buckets. An essential piece of homebrew kit. This Bubbler Airlocks fits into drilled bungs and grommets. Designed specifically for homebrew.It lets the CO² pressure out without letting contamination back in.Just partially fill with water and you're done.

Better Brew Airlock Straight, fits in standard grommets for standard fermenter buckets. An essential piece of homebrew kit. This Bubbler Airlocks fits into drilled bungs and grommets. Designed specifically for homebrew.It lets the CO² pressure out without letting contamination back in.Just partially fill with water and you're done.

Spiral fermenter air lock with red or yellow cap. 10mm diameter.

Fermenter tap with barb (9/12mm) with nut and rubber gasket. Fits holes 25-26mm diameter. Recommended silicone hose inner diameter for the nipple is 9-10mm.

Fermenter Tap Classic 3/4" with Nut and rubber gasket. Fits holes 25-26mm diameter. Fits rigid bottle fillers (not hoses) with ca 11mm diameter.

Better Brew Lever Tap with Nut. With gasket. Fits 26mm holes in fermenters. Nozzle outer diameter is 11,5mm.

Rubber Seal for Airlock that fits 15L and 30L fermenters.

Hop filter in stainless steel, perfect for dry hopping beer in Cornelius kegs or fermenters. Loop for hanging it. Length: 18cm. Diameter: 7cm. Mesh size: 300 microns

Hop filter in stainless steel, perfect for dry hopping beer in Cornelius kegs or fermenters. Loop for hanging it. Length: 29cm. Diameter: 7cm. Mesh size: 300 microns

Thermometer LCD 2-36 degrees Celcius. Self-adhesive. Perfect for the fermenter. Size: 21x148 mm.

Brewly AC-211 Digital Universal Thermostat. EU-version power cord (UK power cord not included). Can control one Heating source and one Cooling source. Sensor included.

Brewly TC-320 Digital Universal Thermostat. EU-version power cord (UK power cord not included).

Inkbird ITC-308 Digital Temperature Controller Outlet Thermostat with Dual Screen Readouts, w/Sensor. For Home Brewing & Fermentation, Breeding & Incubation, Greenhouse, Kombucha.- Plug and play design, easy to use. - Support reading with Centigrade or Fahrenheit. - Maximum output load: 1100W(110V) / 2200W(220V). - Temperature calibration, Compressor delay protection for refrigeration control.- High and low temperature alarms are available. - Dual relay output, be able to connect with refrigeration and heating equipment at the same time. - Dual display window, be able to display measured temperature and set temperature at the same time. - Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.Specifications- Temperature Control Mode :On/Off Control, Heating and Cooling - Temperature Control Range : -40~100 °C / -40~212 ° F - Temperature Resolution: 0.1 ° C / 0.1° F ​- Temperature Accuracy: ±1°C (-50 ~ 70°C) / ±1°F (-50 ~ 160° F) - Ambient Temperature: -30~ 75 ° C / -22~ 167 ° F- Input Power: 100 ~240VAC, 50Hz/60Hz - Temperature Control Output: Max. 10A, 100V ~240V AC - Input Power Cable Length: 1.5m (5ft) ​- Output Power Cable Length: 30cm (1ft)- Sensor Type: NTC sensor (Including) - Sensor Length: 2m / 6.56ft ​- Sensor's probe dimension: 50mm x 6mm- Dimension Body: 140x68x33mm (5.5x2.7x1.3inch)- Socket (EU Version): 135x54x40mm (5.3x2.1x1.6 inch)

INKBIRD ITC-310T-B is a dual relay thermostat which can be set to automatically control 12 individual temperatures for 12 time slots. It is widely used for homebrew, aquarium, pet breeding, hatching, fermentation, seed sprouting and etc.12 individual temperatures for 12 time slots: INKBIRD ITC-310T-B can be set 12 individual temperatures for 12 time slots. Once the practical temperature reaches its set temperature, its timer will be started automatically, which will be much better and more precise for the monitored creatures and/or plants.Wide application contexts: INKBIRD ITC-310T-B is widely used for homebrew, aquarium, pet breeding, hatching, barbecue, boiler temperature control, geothermal temperature control, heating pump constant temperature cycle, strain culture fermentation, seed sprouting, electric heating, electric oven, over-temperature protection and automatic temperature control system of all kinds of electrical equipment and etc.Flexible control mode: it supports single mode and cycle control mode; we can choose and/or switch the control mode based on our practical needs.Specifications INKBIRD ITC-310T-BTemperature Control Range: -50~120°C/-58~248°FTemperature Resolution: 0.1°C / 0.1°FMeasuring Accuracy: ±1°C (-50 ~ 70°C) / ±1°F(-58 ~ 158°F)Temperature Control Mode: On/Off Control, Heating and CoolingTiming Accuracy: 24 hours±1.7sTiming Range: 1~999 (min/hour/day)Periods of Time Max: 12 periodsCycle Setting: 1-999 times cycle, or 00 infinite cycleInput Voltage: 100 ~240VAC, 50Hz/60HzControl Output Current: Max.10AVoltage: 100~240V ACPower: Max.1200W(120V)/2200W(220V)Alarm: High and Low Temperature AlarmSensor Type: NTC Sensor(including)Sensor Length: 2m / 6.56ftRelay Output: Cooling(10A,100-240VAC)Heating(10A,100-240VAC)

Inkbird WiFi ITC-308 Digital Temperature Controller Outlet Thermostat with Dual Screen Readouts, w/Sensor. For Home Brewing & Fermentation, Breeding & Incubation, Greenhouse, Kombucha.- Plug and play design, easy to use. - WIFI smart controller supports both IOS & Android，WIFI supports 2.4GHz Wi-Fi router, free APP “InkbirdSmart” which is able to monitor temperature at any time.- Support reading with Centigrade or Fahrenheit. - Maximum output load: 1100W(110V) / 2200W(220V). - Temperature calibration, Compressor delay protection for refrigeration control.- High and low temperature alarms are available. - Dual relay output, be able to connect with refrigeration and heating equipment at the same time. - Dual display window, be able to display measured temperature and set temperature at the same time. - Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.Specifications- Temperature Control Mode :On/Off Control, Heating and Cooling - Temperature Control Range : -40~100 °C / -40~212 ° F - Temperature Resolution: 0.1 ° C / 0.1° F ​- Temperature Accuracy: ±1°C (-50 ~ 70°C) / ±1°F (-50 ~ 160° F) - Ambient Temperature: -30~ 75 ° C / -22~ 167 ° F- Input Power: 100 ~240VAC, 50Hz/60Hz - Temperature Control Output: Max. 10A, 100V ~240V AC - Input Power Cable Length: 1.5m (5ft) ​- Output Power Cable Length: 30cm (1ft)- Sensor Type: NTC sensor (Including) - Sensor Length: 2m / 6.56ft ​- Sensor's probe dimension: 50mm x 6mm- Dimension Body: 140x68x33mm (5.5x2.7x1.3inch)- Socket (EU Version): 135x54x40mm (5.3x2.1x1.6 inch)

These 29L stainless steel vessels are designed just like a commercial beer keg but with a large 10cm (4inch) tri-clover opening at the top so you can easily get inside the keg to clean it out. This new 29L Size is perfect for doing 20-25L batches so you have a bit of spare head space inside the Kegmenter.This the stainless steel Kegmenter comes with airlock and flat plate however you can also use this kegmenter under pressure if you want to. If you want to use this Kegmenter under pressure then we would recommend that you purchase the lid with ball lock posts and pressure relief vale.The Kegmenter can hold 2.5bar which makes it possible to carbonate and ferment in the same vessel. You can force carbonate using the Pressure Kit (sold seperately).Being able to hold pressure also means you can push the beer out of the fermenter directly through a filter or even dispense directly from fermenter to draft beer tap if you wanted to.SpecificationsVolume: 29L (7.6 Gallons)Maximum Working Pressure: 2.5 BARTest Pressure: 5 BAR Wall Thickness (Body/Chimes): 1.8mm/2.1mmDiameter: 39,5cmHeight: 38cmDatasheetClick here to open the datasheet

These 29L stainless steel vessels are designed just like a commercial beer keg but with a large 10cm (4inch) tri-clover opening at the top so you can easily get inside the keg to clean it out. This new 29L Size is perfect for doing 20-25L batches so you have a bit of spare head space inside the Kegmenter.This the stainless steel Kegmenter comes with airlock and flat plate however you can also use this kegmenter under pressure if you want to. If you want to use this Kegmenter under pressure then we would recommend that you purchase the lid with ball lock posts and pressure relief vale.The Kegmenter can hold 2.5bar which makes it possible to carbonate and ferment in the same vessel. You can force carbonate using the Pressure Kit (sold seperately).Being able to hold pressure also means you can push the beer out of the fermenter directly through a filter or even dispense directly from fermenter to draft beer tap if you wanted to.SpecificationsVolume: 29L (7.6 Gallons)Maximum Working Pressure: 2.5 BARTest Pressure: 5 BAR Wall Thickness (Body/Chimes): 1.8mm/2.1mmDiameter: 39,5cmHeight: 38cmMaterial: 304 Stainless steelDatasheetClick here to open the datasheet

This pressure kit is so you can convert the 29 and 58L Kegmenters into either pressure rated fermenters or use the Kegmenters as ball lock kegs. This lid comes with a red pressure relief valve (that opens at 2.5bar - compatible thread to cornelius type PRVs). The lid has accurately machined gas and liquid posts.This lid is ideally suited to also fermenting under pressure so you can use a spunding valve/adjustable pressure relief valve so you can naturally carbonate during primary fermentation.It should be noted that we now make this lid with a 60cm silicon dip tube with a stainless fload. This innovative design means when you draw liquid from this kegmenter the liquid will always be drawn from the top 2.5cm of liquid meaning only the clearest wort/beer will be drawn from the kegmenter. This is particulrly useful if you are dispending directly from the fermenter or simply want to separate clear liquid from sediment which has sunken to the bottom of the kegmenter.

Ferment with stainless steel like the pros! A high quality stainless steel fermenter with seamless inside for easy cleaning to prevent contamination. It has a 25 L capacity with litre measurements stamped on the inside body and handles for easy lifting. This also comes with a bung and bubbler airlock. Mangrove Jack's Stainless Steel Fermenter 25L- 25 L Capacity- Stainless steel tap- High grade, #304, scratch resistent, stainless steel body- Litre measurements stamped on the inside body of fermenter- Height = 520mm (to top of lid)- Height = 620mm (including vintage airlock)- Height = 480mm (to top edge without lid)

The SF70 is our largest and tallest fermenter yet. With a 70L capacity it’s designed to hold big batches of wort after a big brew day. The SF70 can be adapted to suit your brewing space with an adjustable leg height and castor wheels for easy manoeuvrability. Its intuitive design, 304 grade stainless steel build, and 113° angle conical makes both fermentation and cleaning easy. FEATURESSF70 body built out of high grade, 304 stainless steel113° angle conical avoids yeast and sediment getting stuck to the sides of the coneAdjustable leg height and castor wheels for easy manoeuvrabilityEasily dump yeast with a separate valveInsert temperature probes into the built-in thermowell for accurate temperature readingsTransfer and take samples above the yeast and trub line with an accessible valve on the side of the unit Compatible with the GCA for accurate temperature controlWe’re confident that our products will produce professional results, just like the craft breweries. That’s why every SF70 comes with a 2-year warranty.WHAT'S INCLUDED?- Grainfather SF70- Stainless steel lid with 38mm tri-clamp fitting- Rubber bung & airlock- Thermowell (use with GCA or thermometer)- Cone mounted 10mm stainless steel barbed sample valve- 19mm bottom mounted stainless steel dump valve- Adjustable and removeable legs with castor wheelsSize: 1300 x 410mm (including air lock and in highest leg position)Weight: 13kgCapacity: 70LMax fermentation volume: 65LPower: NoneConnectivity: NoneCone angle: 113°

The Grainfather Conical Fermenter Pro Edition allows you to control the heating of your unit (and cooling with the Glycol Chiller available separately), dump yeast, take samples and transfer your wort via our innovative dual function valve design. Note: EU-version power cord (UK power cord NOT included).Ferment like never before! The Grainfather Conical Fermenter give the brewer professional fermentation control, just like the commercial breweries. Fermentation is arguably the most important part of producing a good quality beer. A good fermentation environment starts with a clean and sterile fermenter, has a consistent controlled temperature base and exposure to oxygen is minimised. The Grainfather Conical Fermenter provides you with a modular system for all of this and more!FEATURESDouble Walled: A stainless steel double walled skin is filled with a thick layer of polyurethane foam for insulation. This is what keeps the wort at a constant stable temperature with minimal influence from any external environmental temperature changes, providing insulation for your fermentation that a standard jacket cannot achieve. Integrated Gentle Heating: In the cavity of the fermenter between the outer body and cone sits a 30 Watt, 12V heating element. Unlike standard heating elements/sources that directly heat the liquid, this heat source is designed to heat the environment in between the walls of the fermenter, which in turn heats the liquid. It is similar to controlling the temperature in a temperature controlled room. The fermenter acts as an artificial environment which can be heated, meaning the temperature is raised in an even and controlled manner which is much better for the yeast. Integrated Cooling Sleeve: In between the two stainless steel walls sits a cooling sleeve (also made of stainless steel). This cooling sleeve is welded onto the inner wall of the fermenter and can be hooked up to the additionally purchased Glycol Chiller. Temperature is dialed into the Temperature Controller and as the cooling liquid travels through this sleeve, it cools the stainless steel which in turn evenly cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, it is completely concealed, built into the fermenter and never needs cleaning or sanitising - a true innovation for a fermenter of this scale.Easy Access to the Interior for Hassle Free Cleaning: The Grainfather Conical Fermenter has a smooth interior with no additions such as cooling coils or additional sampling valves meaning it is easy to clean and minimises the risk of infection.Golden Angle Conical:The conical shape of the fermenter is typical for professional breweries. Our conical has been designed with the 'Golden Angle' of 60º. This is the optimum angle for yeast and sediment to drop down to the bottom of the cone without getting stuck to the sides, allowing you to transfer from above the sediment line, resulting in clearer beer. The conical shape also allows for better mixing during fermentation due to the path of convention currents that it enables to occur. Dual Valve Tap: Make the yeast dumping, transferring and sampling process more professional with this innovative all in one valve. Sampling and transferring is done through an inlet above the sediment line, allowing for clear, sediment free beer. Easily collect your yeast from below the sediment line with the same unique valve for recultivating and pitching. The innovative design of the valve allows for this dual functionality and less cleaning for you. Temperature Control: The Temperature Controller easily snaps on via magnets and pogo pins. Allowing you to accurately dial in a temperature and even set a temperature schedule/profile (you can set up to 4 profiles each with 5 stages). It can control the heating of the integrated heating element and the cooling (if you have upgrade to the Glycol Chiller). Support: The Grainfather Conical Fermenter is fully supported around the world by a fantastic support team who love brewing just as much as you do. Our support team is here for any technical enquiries on brewing or how the Conical Fermenter works, as well as general customer service enquiries.

 All Grainfather Conical Fermenters come with a 24 month warranty. EU-power plug (UK-plug not included)

The Grainfather Conical Fermenter Pro Cooling Edition allows you to control the heating of your unit, dump yeast, take samples and transfer your wort via our innovative dual function valve design. Note: EU-version power cord (UK power cord NOT included).The Cooling Pump Kit allows users of the Grainfather Conical Fermenter to control the fermentation temperature with cold water by pumping it through the double walled insulated interior.Ferment like never before! The Grainfather Conical Fermenter give the brewer professional fermentation control, just like the commercial breweries. Fermentation is arguably the most important part of producing a good quality beer. A good fermentation environment starts with a clean and sterile fermenter, has a consistent controlled temperature base and exposure to oxygen is minimised. The Grainfather Conical Fermenter provides you with a modular system for all of this and more!FEATURES:Double Walled: A stainless steel double walled skin is filled with a thick layer of polyurethane foam for insulation. This is what keeps the wort at a constant stable temperature with minimal influence from any external environmental temperature changes, providing insulation for your fermentation that a standard jacket cannot achieve. Integrated Gentle Heating: In the cavity of the fermenter between the outer body and cone sits a 30 Watt, 12V heating element. Unlike standard heating elements/sources that directly heat the liquid, this heat source is designed to heat the environment in between the walls of the fermenter, which in turn heats the liquid. It is similar to controlling the temperature in a temperature controlled room. The fermenter acts as an artificial environment which can be heated, meaning the temperature is raised in an even and controlled manner which is much better for the yeast. Integrated Cooling Sleeve: In between the two stainless steel walls sits a cooling sleeve (also made of stainless steel). This cooling sleeve is welded onto the inner wall of the fermenter and can be hooked up to the Cooling Pump Kit. Temperature is dialed into the Temperature Controller and as the iced cold water travels through this sleeve, it cools the stainless steel which in turn evenly cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, it is completely concealed, built into the fermenter and never needs cleaning or sanitising - a true innovation for a fermenter of this scale.Basic Cooling Pump Kit: The Cooling Pump Kit allows users of the Grainfather Conical Fermenter to control the fermentation temperature with cold water by pumping it through the double walled insulated interior.Easy Access to the Interior for Hassle Free Cleaning: The Grainfather Conical Fermenter has a smooth interior with no additions such as cooling coils or additional sampling valves meaning it is easy to clean and minimises the risk of infection.Golden Angle Conical:The conical shape of the fermenter is typical for professional breweries. Our conical has been designed with the 'Golden Angle' of 60º. This is the optimum angle for yeast and sediment to drop down to the bottom of the cone without getting stuck to the sides, allowing you to transfer from above the sediment line, resulting in clearer beer. The conical shape also allows for better mixing during fermentation due to the path of convention currents that it enables to occur. Dual Valve Tap: Make the yeast dumping, transferring and sampling process more professional with this innovative all in one valve. Sampling and transferring is done through an inlet above the sediment line, allowing for clear, sediment free beer. Easily collect your yeast from below the sediment line with the same unique valve for recultivating and pitching. The innovative design of the valve allows for this dual functionality and less cleaning for you. Temperature Control: The Temperature Controller easily snaps on via magnets and pogo pins. Allowing you to accurately dial in a temperature and even set a temperature schedule/profile (you can set up to 4 profiles each with 5 stages). It can control the heating of the integrated heating element and the cooling via the Cool Pump Kit. Support: The Grainfather Conical Fermenter is fully supported around the world by a fantastic support team who love brewing just as much as you do. Our support team is here for any technical enquiries on brewing or how the Conical Fermenter works, as well as general customer service enquiries.

 All Grainfather Conical Fermenters come with a 24 month warranty. EU-power plug (UK-plug not included)

The GF30 Coat is the perfect fitment for those in a climate that experiences high condensation rates when using either using the GC4 Glycol Chiller or Cooling Pump Kit to lower the fermenter’s temperature. Fits Grainfather Conical Fermenter.Features:Made from high quality 5mm thick SBR foam.Consists of two independent sections for both the main body and the fermenter cone for total coverage.

Temperature control is one of the most crucial elements for producing a good quality beer. It needs to be regulated and stable throughout the whole fermentation process to ensure the yeast doesn't get stressed and ferments correctly to get the right flavour profile. The pump can handle cold water and glycol.To be able to cool with the Grainfather Conical Fermenter, you need to have the Conical Fermenter Temperature Controller. Then once your target temperature is below the temperature of the wort in your fermenter the Cooling Pump Kit pumps ice cold water or Glycol through the double walled insulated interior to cool down your wort. Simply connect the couplers and insulated hoses to the Conical Fermenter, submerge the submersible pump into a cooler box with water (add ice for your required temperature) and pump the liquid through the insulated cooling sleeve of the Conical Fermenter body.- Conical Fermenter Cooling Pump (submersible) that can handle Glycol.- T-section power connector.- 2 x brass couplers.- Rated 12 VDC – 4.8 Watts.

The Grainfather Digital Temperature Controller replaces the temperature display. With this you can control the heating and the cooling (if you have the Grainfather Glycol Chiller) of your fermenter by dialing in a temperature or even setting a temperature schedule (can set up to 5 stages). This snaps on easily via magnets and pogo pins with no extra cords or clutter.Control the heating element and Glycol Chiller (available separately)Choose between imperial and metric (C° & F°)Total of 4 fermentation profiles with up to 5 steps each (2 are pre-set for a lager and an ale, 2 are custom)Hysteresis is customisable and able to be set at 0.1 intervals between a range of 0.1°C – 1.9°C & 0.2°F - 2.9°F (the default setting is 0.5°C)

Make the yeast dumping, transferring and sampling process more professional with this innovative all in one valve. Sampling and transferring is done through a valve above the sediment line, allowing for clear, sediment free beer. Collect your yeast from below the sediment line for recultivating and pitching. - Dual Valve Tap with 110 mm (4.3”) liquid inlet

Grainfather Pump & Adapter for Conical Fermenter. NOTE! Spare part.

New version with touch panel (LED). Control your fermentation temperature accurately, every time! Temperature control is one of the most crucial elements for producing a good quality beer. It needs to be regulated and stable throughout the whole fermentation process to ensure the yeast doesn't get stressed and ferments correctly to get the right flavour profile. With the ability to individually power and control the temperature of up to four Grainfather Conical Fermenters, each with their own fermenting schedules, the Grainfather Glycol Chiller is the perfect addition to ensure superior fermenting results.Design:With a sleek and compact design, that still accommodates our full array of features, the Glycol Chiller maintains the Grainfather’s principle of providing quality home brewing equipment, that deliver’s craft brewery like results, on a small footprint. With the addition of the Glycol Chiller, your system is operating at the ultimate level and you are even able to cold crash and lager down to 4°C (39°F). The Glycol Chiller connects to a hidden cooling sleeve, located in between the two stainless steel walls of the Conical Fermenter. Your desired temperature is dialed into the digital temperature controller on the Conical Fermenter, the liquid then travels through this sleeve, cooling the stainless steel which in turn cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, is completely concealed and does not need cleaning or sanitising - a true innovation for a fermenter on this scale.Features:- Allows you to cold crash 23 L (6 US Gal) of wort to as low as 4-6ºC (39-43°F). Minimum temperature will vary based on external factors such as ambient room temperature, the number of fermenters connected and other environmental conditions.- Cools and powers up to 4 Conical Fermenters at different temperatures and fermenting schedules.Note: The instructions for the Glycol Chiller will be attached to the outside of the shipping box. It is important that you retain these, do not throw them away and read them carefully before use to ensure no damage occurs to the unit. If these for any reason are not included with your purchase, we highly recommend you download a new copy via the instructions tab on this page and read them carefully.Glycol Chiller includes:- Wall outlet power cord with plug- 2 x cooling connection couplers- 2 x 2 m (6.5 ft) insulated hoses- 1 x Glycol Funnel- 1 x silicon tube for priming pump- 1 x 3 L (3 US qt) propylene glycolNOTE: When you receive your unit, you will need to fill it up with a propylene glycol mixture. Refer to the instructions provided with the Glycol Chiller for mixing, filling and pump priming information.Warranty:There is 24 month warranty for Glycol Chillers. Specifications:- Touch LED display panel- 6 L (1.5 US Gal) glycol tank- 300 W- 220 – 240 V, 50Hz- Noise level (operating): 50-60 dB- EU-version power cord (UK power cord NOT included).- 390W x 450D x 656H (mm)- Weight: 28.3 kg (62 lbs)InstructionsClick here to open the manual

With the Grainfather Glycol Chiller Adapter (GCA), you can easily control the temperature of your fermenter together with the Grainfather Glycol Chiller. Can be used in several models of fermenters and has both cooling and heating to provide a stable fermentation temperature.The kit consists of a cooling coil that is mounted through a rubber bung, which also has room for a airlock or blow-off, down into the fermenter. This coil is then connected to one of the channels on the Clycol Chiller.The control unit is of the same model as in Grainfathers Conical Fermenter Pro and handles the heating element and the glycol cooler's coolant pump to regulate temperature in the fermenter. It also supports Wi-Fi and the Grainfather App, which offers the user the ability to monitor and control the fermentation remotely. The unit's temperature probe is mounted on the outside of the fermenter or in a thermowell.The heating element is 30 W and is mounted with self-adhesive tape on the side of the fermenter.Specifications:Heating element - 12 V, 30 W. Dimension: 22 x 8 cm. Cord 2 mCooling coil - 5 m, 9 mm pipe outer diameter. The coil is 12 cm wide and 52 cm highTemperature probe - 35 x 6 mm. Cord 2 mControl unit - 12V. WiFI support, color display, Power cord 2 m.Cooling connection hoses - Insulation. length 2 meters, inner diameter 8 mm

Propylene Glycol Pure 1L 99,8%. Food grade. Can also be used with Grainfather Glycol Chiller for example. Volume 1L.

Original Propylene Glycol for Grainfather Glycol Chiller for example. Volume 3L.

All you need is a C02 bottle and a regulator to attach to the Pressure Transfer and you can transfer your beer into a keg or bottles through the Conical Fermenter Dual Valve Tap or via the top of the fermenter lid using the Beer Racking Pipe.Package includes- High quality 304 stainless steel components- Accurate digital pressure gauge- Needle valve for precise control of pressureNOTE: Batteries are not included for the Pressure Gauge. 2 x AAA batteries are needed.

Glass jar 4L with lid and tap with many uses, such as: fermentation of beverages such as Kombucha, for cold beverages such as beer, cider, wine, juice, ice water or lemonade.Note: During fermentation, the lid must be slightly open, with eg. a muslin bag in between. The lid must be opened a little to make the tap work, this is due to that a vacuum is formed in the glass when the lid is on. Must NOT be pressurized.- Capacity: 4 liters- Dimensions (approx.): 27 x 16 x 16.5 cm (HxWxD)- With lid and tap.- Hand wash only.- Not for hot drinks.

Now with Tri-Clover Clamp for easy assembly and disassembly of the conical tank, Butterfly valve and harvesting container. No more difficult and complicated Butterfly valve. Now it is easy and simple to mount Butterfly valve with the Tri-Clover Clamp. See video below.FermZilla revolutionary design simplifies the home brewing process and minimizes the risks of infection and oxidation. Finally, you can brew your beer and dispense directly to bottles or drink it as draft beer – without touching the beer. You can carbonate your beer naturally in the FermZilla, or at your desired pressure with the optional pressure kit and the additional pressure release valve with gauge.Facts:27 L. Conical tankWorking pressure: 2.4 bar (35 psi)FermZilla Tri-Conical Starter kit Gen-3 - 27 L. contains:1 x 27 L. Conical tank with metal neck ring1 x Butterfly valve with Tri-Clover Clamps1 x 3" Tri-Clover Clamp1 x 2" Tri-Clover Clam1 x Reinforced stainless steel frame1 x Lidt with red pressure release valve 2,4 bar/35 psi, 2 x Male Cap Threads, with caps and the possibility to drill 4 ports for accessories1 x  600 ml yeast harvesting container with 2 x Male Cap Threads and caps.1 x Airlock1 x Stainless Steel Handle Assembly1 x Strip Stick On Thermometer1 x Level indicator sticker (Litres and Gallons)1 x Spare O-RingDo not expose to liquid temperatures above 55°C / 130°F or ambient temperatures above 35°C / 95°F.Warnings:Please read instructions thoroughly before use. The current version can be found in the 'instructions' tab above. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.Do not expose to liquid temperatures above 55°C / 130°F or ambient temperatures above 35°C / 95°F.

Now with Tri-Clover Clamp for easy assembly and disassembly of the conical tank, Butterfly valve and harvesting container. No more difficult and complicated Butterfly valve. Now it is easy and simple to mount Butterfly valve with the Tri-Clover Clamp. See video below.FermZilla revolutionary design simplifies the home brewing process and minimizes the risks of infection and oxidation. Finally, you can brew your beer and dispense directly to bottles or drink it as draft beer – without touching the beer. You can carbonate your beer naturally in the FermZilla, or at your desired pressure with the optional pressure kit and the additional pressure release valve with gauge.Facts:55 L. Conical tankWorking pressure: 2.4 bar (35 psi)FermZilla Tri-Conical Starter kit Gen-3 - 55 L. contains:1 x 27 L. Conical tank with metal neck ring1 x Butterfly valve with Tri-Clover Clamps1 x 3" Tri-Clover Clamp1 x 2" Tri-Clover Clam1 x Reinforced stainless steel frame1 x Lidt with red pressure release valve 2,4 bar/35 psi, 2 x Male Cap Threads, with caps and the possibility to drill 4 ports for accessories1 x  1000 ml yeast harvesting container with 2 x Male Cap Threads and caps.1 x Airlock1 x Stainless Steel Handle Assembly1 x Strip Stick On Thermometer1 x Level indicator sticker (Litres and Gallons)1 x Spare O-RingDo not expose to liquid temperatures above 55°C / 130°F or ambient temperatures above 35°C / 95°F.Warnings:Please read instructions thoroughly before use. The current version can be found in the 'instructions' tab above. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.Do not expose to liquid temperatures above 55°C / 130°F or ambient temperatures above 35°C / 95°F.

The FermZilla 30L All Rounder is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating and dispensing. Incl. Fermenter body, stainless steel frame, airlock and lid with red pressure relief valve. Pressure rated up to 2.5bar.This kit includes:1 x All rounder tank1 x 304 stainless stand1 x Airlock1 x Pressure rated lid1 x Digital temperature sticker1 x Red 2.5bar pressure relief valve1 x Graduation StickerEasy to CleanThis fermenter is made from super smooth PET so it's easy to clean. Just use s small scoop of Powerful Brewery Wash and wipe it clean after a 5 minute soak. No scrubbing necessary.Large 120mm OpeningThe opening at the top is signficantly larger then the older Snub Nose or other similar fermenters. This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.Pressure RatedThis fermenter is rated up to 2.5bar so you can force carbonate just like a keg. You can use this fermenter for closed transfers and signficiantly reduce oxygen exposure.Crystal ClearThe wall of the All Rounder is crystal clear so you can see what's going on inside. This makes it really easy to determine visually how the fermentation, how the yeast is floculating etc.ImpermeableThe PET plastic is not permeable like some other fermenters made from PP or HDPE. The fermenter wall is a much better gas barrier keeping your product fresher for longer.No Flavour and Aroma Carry OverOther HDPE fermenters tend to be so pourous they carry flavour and aromo from one batch to another. Robust and Difficult to DamageImpossible to smash like glass. The tank is impact resistant but light weight and easy to use.IMPORTANT NOTE: This tank should not be used for hot liquid. Do not put liquids inside this tank over 50C. It will melt the tank. Also this tank comes pressure tested however we recommend that every 2 years you re-hydro test this tank yourself. Please contact us for more information regarding how to hydro test when the time comes.

The FermZilla 60L All Rounder is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating and dispensing. Incl. Fermenter body, stainless steel frame, airlock and lid with red pressure relief valve. Pressure rated up to 2.5bar.This kit includes:1 x All rounder tank1 x 304 stainless stand1 x Airlock1 x Pressure rated lid1 x Digital temperature sticker1 x Red 2.5bar pressure relief valve1 x Graduation StickerEasy to CleanThis fermenter is made from super smooth PET so it's easy to clean. Just use s small scoop of Powerful Brewery Wash and wipe it clean after a 5 minute soak. No scrubbing necessary.Large 120mm OpeningThe opening at the top is signficantly larger then the older Snub Nose or other similar fermenters. This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.Pressure RatedThis fermenter is rated up to 2.5bar so you can force carbonate just like a keg. You can use this fermenter for closed transfers and signficiantly reduce oxygen exposure.Crystal ClearThe wall of the All Rounder is crystal clear so you can see what's going on inside. This makes it really easy to determine visually how the fermentation, how the yeast is floculating etc.ImpermeableThe PET plastic is not permeable like some other fermenters made from PP or HDPE. The fermenter wall is a much better gas barrier keeping your product fresher for longer.No Flavour and Aroma Carry OverOther HDPE fermenters tend to be so pourous they carry flavour and aromo from one batch to another. Robust and Difficult to DamageImpossible to smash like glass. The tank is impact resistant but light weight and easy to use.IMPORTANT NOTE: This tank should not be used for hot liquid. Do not put liquids inside this tank over 50C. It will melt the tank. Also this tank comes pressure tested however we recommend that every 2 years you re-hydro test this tank yourself. Please contact us for more information regarding how to hydro test when the time comes.

FermZilla Hop Bong is a versatile accessory, capable of pressurized dry hopping and oxygen purged hops into fermenters. And also as an inline carbonation/oxygenation accessory.Capacity in Hop Pellets:150g to 180gNamed purely on its looks and not its function. The Hop Bong is a versatile pressurizable tri-clover accessory, capable of not only dry hopping oxygen purged hops into fermenters. But also as an inline carbonation/oxygenation accessory.This is a completely new pressure pack for the basic FermZilla Tri-Conical and All Rounder Fermenters with the new 2" Tri-Clover Adapted Pressure Lid.Constructed from Nylon 12: An autoclavable, extremely robust, and chemical resistant engineering plastic.Includes:1 x KL05333 Red 35psi PRV1 x KL20176 PCO1881 PRV Cap1 x KL23627 - PCO1881 Male x 2 Inch Tri-Clover (POK)3 x KL03438 - 2 Inch TC Clamp Beaded Seal3 x KL03322 - 2 Inch TC 2 Segment Clamp1 x KL26079 - 2 Inch Hop Bong1 x KL10788 RED Multi Gas Post Plastic Carbonation Cap1 x KL27564 - 2 Inch x 2 Inch Butterfly Valve1 x KL22569 Yellow 17psi PRV1 x KL35965 - 4 Inch TC Pressure Lid with 2 Inch TC PortPlease note that the Hop Bong is not made from glass. It is made from special engineering plastic.

The valve makes it possible to dry hop with a regular soda bottle on a FermZilla. You put some hops in a threaded bottle, attach the valve, and put it onto the lid of the FermZilla. An easy and cheap tool for dry hopping.If you also use a Carbonation Cap T-Piece and a Line Cleaning and Carbonation Cap you will be able to use Co2 to remove the oxygen from the hops.Stainless steel ball valve with a approx. 20 mm bore and O-ring in both ends.

Add this pressure kit to your FermZilla 27L, 35L or 55L and turn your FermZilla into a true uni tank that can be used for carbonating beer. This inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:Fermenting Under Pressure:First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Pushing, and Serving:When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Lack of OxidationBecause the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:• Ferment beer under pressure to reduce ester and fusel alcohol production• Ability to always draw clear beer with the unique, floating draw tube • Keg already carbonated beer• Use co2 to push beer into a keg or though a filter into a keg• Carbonate and serve beer directly from the FermZilla, eliminating kegging all togetherFermZilla Red Plastic Pressure Kit includes:- 2 x Carbonation Screw Caps with barb- 1 x FermZilla 27L, 35L & 55L SS Floater & 60cm Silicone Dip Tube

Add this pressure kit to your FermZilla 27L, 35L or 55L and turn your FermZilla into a true uni tank that can be used for carbonating beer. Stainless steel.This inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:Fermenting Under Pressure:First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Pushing, and Serving:When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Lack of OxidationBecause the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:• Ferment beer under pressure to reduce ester and fusel alcohol production• Ability to always draw clear beer with the unique, floating draw tube • Keg already carbonated beer• Use co2 to push beer into a keg or though a filter into a keg• Carbonate and serve beer directly from the FermZilla, eliminating kegging all togetherFermZilla Stainless Pressure Kit includes:- 2 x Carbonation Screw Caps with barb- 1 x FermZilla 27L, 35L & 55L SS Floar & 60cm Silicone Dip Tube

The filter prevents hop residue etc from beeing sucked up into the silicone hose of the FermZilla Float. Made from HDPE and 304 Grade stainless steel this product can be boiled or sanitized with most detergents.The float can be mounted in three different places on the filter, to determine how close to the surface you want to suck up liquid.Dimensions: 40.5 x 27 mm. Hose holder diameter: 7.20 mm, perfect for 6mm inner diameter silicone tube/hose. Materials: Stainless steel and plastic. design may vary.

FermZilla 60cm silicone dip tube and stainless float. Ensure that only the top layer of beer is poured from the Fermzilla/Fermentasaurus.

Fits CO2/Beer Ball-lock-coupling. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Stainless steel.

Fits CO2/Beer Ball-lock-coupling and has 1/4" (6,5mm) stem. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Red plastic.

Fits CO2/Beer Ball-lock-coupling and has 1/4" (6,5mm) straight stem. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Yellow plastic.

Turn your soda bottle into a smart growler quick and easy! Mount either a plastic or metal line cleaning & carbonation cap to the tee piece. Afterwards you are able to connect both a Co2 and liquid ball lock at the same time, so you can take a regular soda bottle and turn it into a growler.Note: This is for the tee piece only, you need to buy the remaining products seperatly.Do not exceed 4,5 Bar/ 65 Psi

Fermzilla chiller. Provides the possibility of temperature control during fermentation using, for example, glycol coolers. Of course, the spiral also fits in other vessels with sufficiently large opening. Are installed by drilling two 22 mm holes in the lid. It is attached using the supplied Duotight bushings. The tube dimension is compatible with 3/8 "(9.5 mm) quick couplings. The length can be reduced by means of a pipe cap. See proposed accessories below.

Thermowell of 60 cm for mounting in the lid of Fermzilla. Inner diameter is 7 mm, enough room for most temperature probes such as Inkbird.

Insulated Jacket for Fermzilla 27L designed to insulate your FermZilla and to obtain a correct temperature.

Insulated Jacket for Fermzilla 55L designed to insulate your FermZilla and to obtain a correct temperature.

This yeast collection container can fit the FermZilla fermenters and is primarily used for collection and addition of hops and yeast via the butterfly valve. NOTE: One yeast collector is already included in the FermZilla Kits.This collection container can also be used for yeast starters meaning that you can create the yeast starter in this collection container directly then attach to the valve of the FermZilla so you can pitch yeast without needing to open the lid. This collection container has been designed to work with the magnetic stirrer machine.The ports on the side of this collection container are the same as a standard coke bottle or soft drink bottle. The threads are designed to suit the stainless carbonation caps. These carbonation caps will enable you to purge oxygen for dry hopping, attach carbonation stone and carbonate liquid in the FermZilla, oxygenate wort and are useful for many other reasons.FermZilla Yeast Collector 1L features:- This collection container fits all the FermZilla conical fermenters.- The clear body is made from Tritan from Eastman Plastics. This heat tolerant plastic is BPA, and plasticiser free.- The Lid is made from impact resistant HDPE.- Both lid and body can handle boiling wort.- Height: 150 mm- Diameter: 115 mm- Capacity: 1L

FermZilla Yeast Collector O-ring Packning. Spare part.

FermZilla Plastic Lid. Spare part.

Fermzilla Lid Ring replacement part.

Spare part. FermZilla Lid Seal O-ring. Fits FermZilla 27L, 35L and 55L.

Fermzilla Conical Valve Assembly with the conical plastic part, conical gasket, O-ring and Threaded lid ring.

We have taken all the best from Ferminator Basic and made a new version with WiFi and Bluetooth. It is now possible to control your Ferminator online and see current temperatures and settings. In BrewCreator you can enter data about your brew and see all information about your Ferminator Connect. The whole thing is gathered in a nice detailed graph, where you can follow the course of the temperature and see the changes that have been made. Ferminator Connect can also communicate directly with Graviator - a wireless hydrometer measuring directly inside your fermenter (bought seperately). At room temperature (20 °) the temperature can be lowered to 0 ° or increased to 50 ° *. A powerful thermoelectric Peltier element that stands for the cold, the fan dissipates the heat generated in the process. The height of the Ferminator can be easily expanded with 22cm high expansion modules that are purchased separately. In the Basic version, there is room for, for example, a 30L plastic fermenter or a 30L Fermzilla Flat Bottom. Ferminator Ferminator is a revolution in temperature-controlled fermentation. With a Ferminator it is now possible to ferment at a precise and stable temperature. At room temp. (20 °) the Ferminator can lower the temp. to 0 ° and raise it to 50 ° *. The height can easily be extended with optional 22cm high expansion modules (buy seperately). - The Ferminator makes is possible to ferment at the precise desired temperature. For example, it is possible to ferment a pilsner or lager at the proper low temperature or an ale at high temperature to achieve lots of desired esters. - The Ferminator keeps the temperature constant during the fermentation process and can of course be adjusted at any time. A constant fermentation temperature ensures unwanted flavor notes can be avoided and that the yeast will go into a hibernation state. - The Ferminator gives you full control over the fermentation and lets you experiment with completely new flavor notes and profiles. Cooling / Heating Unit - At room temperature (20 ° C) the Ferminator can lower the temperature to 0C and raise the temperature to 50 ° C *. - Lowers temperature down to 20 ° C relative to ambient temp *. - Raises the temperature up to 30 ° C relative to ambient temp *. - The built-in fan ensures evenly temperature throughout the Ferminator. - The control unit is easily programmed and displays the actual temperature and set temperature. - The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid. - Maximum power consumption: 75 Watts, standby: 1 Watt. * Tested with Ferm inator Basic, when using expansion modules, an additional Cooling / Heating Unit may be required. Ferminator Connect - Dimensions outside: 560 L x 560 B x 651 H - Dimensions inside: 436 L x 436 W x 531 H Size fits: 32 L. Fermenter 30 L. FermZilla Flat Bottom Material Ferminator is made in EPS. Optional Expansion (Not Included, buy it seperately below) Expansion Module The expansion module has a height of 22 cm. The Ferminator can be expanded with several expansion modules an additional cooling / heating unit on the back. The expansion module and Ferminator can be disassembled taking up minimal storage space. Note that some product images contain extra equipment not included.

Ferminator is a revolution in temperature-controlled fermentation. With a Ferminator it is now possible to ferment at a precise and stable temperature. At room temp. (20°) the Ferminator can lower the temp. to 0° and raise it to 50°*. The height can easily be extended with optional 22cm high expansion modules (buy seperately).The Ferminator makes is possible to ferment at the precise desired temperature. For example, it is possible to ferment a pilsner or lager at the proper low temperature or an ale at high temperature to achieve lots of desired esters.The Ferminator keeps the temperature constant during the fermentation process and can of course be adjusted at any time. A constant fermentation temperature ensures unwanted flavour notes can be avoided and that the yeast will go into a hibernation state.The Ferminator gives you full control over the fermentation and lets you experiment with completely new flavour notes and profiles.Cooling/Heating Unit- At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50°C*.- Lowers temperature down to 20°C relative to ambient temp*.- Raises the temperature up to 30°C relative to ambient temp*.- The built-in fan ensures evenly temperature throughout the Ferminator.- The control unit is easily programmed and displays the actual temperature and set temperature.- The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid.- Maximum power consumption: 75 Watts, standby: 1 Watt. *Tested with Ferminator Basic, when using expansion modules, an additional Cooling/Heating Unit may be required.Ferminator Basic- Dimensions outside: 560 L x 560 B x 651 H- Dimensions inside: 436 L x 436 B x 531 HSize fits:32 L. Fermenter30 L. FermZilla Flat Bottom MaterialFerminator is made in EPS.Optional Expansion (Not Included, buy it seperately below)Expansion ModuleThe expansion module has a height of 22 cm.The Ferminator can be expanded with several expansion modules an additional cooling/ heating unit on the back. The expansion module and Ferminator can be disassembled taking up minimal storage space.Note that some product images contain extra equipment not included.

Protects the bottom of the Ferminator. The bottom plate has rounded corners and is made of stainless steel.

Ferminator Top Spare part.

Ferminator Bottom Spare part.

Ferminator Insert for hole Spare part. Fits in the hole where the cooling units normally is in Ferminator Top.

The Ferminator can be expanded with an additional cooling/ heating unit on the back, so you have two units that can regulate the temperature. This is a Ferminator Basic unit. At room temperature (20°) the temperature can be lowered to 0 ° or increased to 50 ° *. A powerful thermoelectric Peltier element that stands for the cold, the fan dissipates the heat generated in the process. Ferminator Basic Cooling & Heating Unit - At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50 ° C *. - Lowers temperature down to 20 ° C relative to ambient temp *. - Raises the temperature up to 30 ° C relative to ambient temp *. - The built-in fan ensures evenly temperature throughout the Ferminator. - The control unit is easily programmed and displays the actual temperature and set temperature. - The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid. - Maximum power consumption: 75 Watts, standby: 1 Watt. * Tested with Ferm inator Basic, when using expansion modules, an additional Cooling / Heating Unit may be required. Note that some product images contain extra equipment not included.

The Ferminator can be expanded with an additional cooling/ heating unit on the back, so you have two units that can regulate the temperature. This is a Ferminator Connect unit which can be connected to WiFi and be controlled online by BrewCreator.We have taken all the best from Ferminator Basic and made a new version with WiFi and Bluetooth. It is now possible to control your Ferminator online and see current temperatures and settings. In BrewCreator you can enter data about your brew and see all information about your Ferminator Connect. The whole thing is gathered in a nice detailed graph, where you can follow the course of the temperature and see the changes that have been made. Ferminator Connect can also communicate directly with Graviator - a wireless hydrometer measuring directly inside your fermenter (bought seperately). At room temperature (20°) the temperature can be lowered to 0 ° or increased to 50 ° *. A powerful thermoelectric Peltier element that stands for the cold, the fan dissipates the heat generated in the process. Ferminator Connect Cooling & Heating Unit - Wifi & Bluetooth- At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50 ° C *. - Lowers temperature down to 20 ° C relative to ambient temp *. - Raises the temperature up to 30 ° C relative to ambient temp *. - The built-in fan ensures evenly temperature throughout the Ferminator. - The control unit is easily programmed and displays the actual temperature and set temperature. - The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid. - Maximum power consumption: 75 Watts, standby: 1 Watt. * Tested with Ferm inator Basic, when using expansion modules, an additional Cooling / Heating Unit may be required. Note that some product images contain extra equipment not included.

Upgrade the Ferminator to a fullblood draft beer system with a simple plug and then pour craft beer straight away. Plug & Pour is an easy solution for transforming the Ferminator to a draft beer system with 2 taps.The following is included in Ferminator Plug & Pour Drip Tray - 2 Taps:• Plug & Pour mounting plate• Ferminator Drip Tray• Ferminator Strap• Ferminator Insert• 2 xTaps with flow control• 2 x Shanks• 2 x Ball Locks fluid• 2 x Ball Locks Co2 • Tube for liquid• Tube for Co2• Doutight fittings• T-Piece for Co2

Ferminator Power Adapter with cord to that atteched to the Ferminator, and power cord (EU).

The strap holds the top together, ideal if the Ferminator needs to be moved. Can also be ideal when using an extra cooling/heating unit or Plug & Pour.

A wireless hydrometer and thermometer that measures directly in the fermenter, and comminicates to the app BrewConnect via WiFi. It can be used independently in a brewing via WiFi, but the extra smart thing is that it can communicate directly with Ferminator Connect via Bluetooth. This allows a Ferminator Connect to know the exact temperature inside the beer and adjust the temperature even more precisely. The Gravity charger is charged wirelessly via the included wireless charger. It should therefore never be opened, and you avoid the risk of it leaking and destroying a brew. If the Graviator is not charged before brewing, this is not a problem. It can be charged in approx. 5 hours. The improved algorithm in Graviator, the unique design and build quality provide a high accuracy of ± 0.002 SG. The size and weight of the engraver also make it more stable under the crotch.Please observe! The Graviator does not work with steel fermenters.

Graviator Wireless Charger can charge a Graviator of approx. 5 hours. The charger follows the Qi standard and can charge with 5W / 7.5W / 10W. This charger will also work with your phone if it's Qi-enabled.

The RAPT Pill provides accurate real-time density (SG) and temperature measurement and control via the WiFi/Bluetooth integration with the RAPT mobile app/RAPT IOT. Made to measure in your fermenter!RAPT Pill provides accurate specific gravity (SG) and real-time temperature logging and control via wifi/bluetooth. The RAPT pill functions as both a hydrometer and thermometer for real-time gravity testing, enabling instant gravity and temperature measurements and also logs from inside the fermenter during fermentation.The RAPT Pill has many advantages over other wireless hydrometers and thermometers including rugged design, better ergonomics, sanitary design and less prone to errors as a result of hops, krausen or CO2 bubbles generated from fermentation.Specifications:The RAPT Pill is approximately 37mm x 125mm - compact enough to fit almost anywhere!Note:Make sure the RAPT pill is charged for 24 hours before use. This is to ensure that it is fully charged and that the battery is calibrated.When the RAPT Pill is connected via USB-C and connected to wifi, the firmware will automatically update to the current version (if needed). Pill must be connected via USB-C and connected to Wi-Fi to receive firmware updates. What is RAPT?RAPT IOT Hub is a free service where all RAPT-enabled products can both log and store data to the hub where you can conveniently access this data. The RAPT hub can also allow you to remotely control your devices giving you absolute control over your device no matter where you are. The RAPT portal enables you to make complex temperature profiles involving different temperature settings over time, meaning you can start/run a temp profile giving you a set and forget experience. The RAPT portal also controls the alert/notification process for you so that you can receive email notifications if something does not go according to plan.There is no limit to the number of RAPT devices you can connect RAPT IOT Hub. This is unlike other popular wireless hydrometers where you are limited by the number of hydrometers you can connect to an app.Please note: RAPT Pill is fully Wi-Fi and Bluetooth compatible. Currently, it can be fully integrated with wifi. Bluetooth integration will be enabled with a later firmware update.GoogleThe Google Play Android app can be downloaded from the link below.https://play.google.com/store/apps/details?id=io.raptAppleThe Apple App Store RAPT app can be downloaded via the link below.https://apps.apple.com/th/app/rapt/id1573192994"This app is a web mobile wrapper that allows you to browse the RAPT portal/website so that the website is rendered to a mobile device screen increasing the usability on your device. It also gives you the added functionality of push notifications to your mobile device."

Replacement Silicone O-ring for RAPT Pill. It is a good idea to use keg lube to keep these o-rings in the best conditions

Adjustable pressure valve with manometer. Can handle pressures up to 2 bar / 30 psi. 1/4" MFL.

As the FermZilla/Fermentasaurus containers are a pressure vessel thus they require periodic testing. We recommend that you pressure test the Fermentasaurus containers once every 2 years if you want to keep using the fermenter under pressure. This fitting allows you to hydrostatically pressure test the FermZilla/fermentasaurus tank using a keg and regulator. First fill the fermzilla/fermentasaurus to the brim with tap water. This fitting will screw into the pressure relief valve socket on the pressure lid for the fermzilla/fermentersaurus. You would then connect a swivel nut and barb to this fitting, connected to the luqid out of a keg full of water. You can then connect your regulator to the gas in on the keg and pressurises the system to the test pressure.

This jacket is designed to insulate your Fermentasaurus during the colder months to keep your fermentation at the optimum temperature. It can also be used with a heating belt/wrap to warm up the wort if the heat from the fermentation isn't enough.Also completely blocks any light/UV to prevent light-struck beer.

Easy-to-use magnetic stirrer with good capacity. Infinitely variable speed and durable plastic construction that can withstand a little spill. Rotatable stand for e.g. thermometer or pH probe included. Stable base with rubber feet. Ultra silence and vibration-free design. Stackable, which saves space during storage.Material: Durable plastic cover.Speed: Stepless 300-2000 rpm.Capacity: 1.5 liters.Power supply: 12V from the included 230V mains adapter.Max Power: 7,2WDimensions: Diameter top 120 mm, max 160 mm. Height 55 mm without stand, 230 mm with stand.Weight: 300 g.Protection class: IP21Accessories: Stand with holder (for probe max 12 mm) included.

This is a simple, reliable and efficient magnetic stirrer for up to 5L flasks. Excellent speed precision. Remains cold even after several days of continuous use. Ensures a high resistance to chemical agents. - High Reliability- Control panel is shielded from liquid spills- Epoxy-coated tough steel casing- Long life operation- Accepts up to 5 liter flasksFeatures- Pale surface for visualization of particles and color changes- Remains cold, even after days of continuous use- Specifically designed for microtitration- Excellent speed control, even at low speed- Simple & Practical- Precision speed regulation up to 1100rpm- Universal mains voltage / frequency range- Light weightTechnical data: Fisher Scientific Microstirrer Magnetic StirrerHeight: 48mmWeight: 0.55KgSpeed: up to 1100RPMMaterial: Epoxy, MetalSpeed Control: Excellent speed control even at low revolutionsSize: 48 H x 120 W x 128 DmmWattage: 0.6WWidth: 120mmVoltage: 100-240VHertz: 50/60HzElectrical Requirements: 100 to 240V, 50/60Hz, 0.6W

Compact magnetic stirrer machine with adjustable speed 0-3600 RPM. Perfect as a yeast starter and propagation of your yeast, up to 3 liters. Power 3W, adaptor with EU-outlet included (12VDC/220V, 1.2m cord). 1pc Magnetic Stir Bar included.Measurements: 12x12cm and 3,2cm heigh.

Tap made in 304 stainless steel that fits most breweries. Rubber covered handle with auto-lock function. 1/2" thread with stainless 1/2" nut and silicone seal. 13mm (1/2") barb at the opening (fits 1/2" hose).

Provides stable stirring action. The PTFE magnetic stir bar work within a wide range of conditions. Smooth, round profile for a wide variety of applications. White PTFE encapsulated Alnico V magnet core. Autoclavable.MeasurementsLength: 40 mmDiameter: 8 mm

PFTE Coated stirr bar magnet without ring for magnetic stirrers. Dimensions: 12x3 mm.

PTFE-coated powerful stirr bar magnet with ring for magnetic stirrers. Dimensions: 27x8 mm.

PTFE-coated powerful stirr bar magnet with ring for magnetic stirrers. Dimensions: 45x8 mm.

PTFE-coated rod for easy pickup of stirr magnets. Strong magnet, withstands heat, cold and has very high chemical resistance. Magnetic stirrer, stirrer magnets and beakers are ordered separately.Material:PTFE-coated metal with strong magnet.Dimensions: Length 345 mm, diameter 10 mm.

Seals for Conical Dual Valve Tap O-rings are a complete set of replacement O-rings for Dual Valve Tap on Grainfather Conical Fermenter.Spare Part.

Grainfather 2" Tri-clamp Gasket for Conical FermenterSpare Part.

Brewtools HopDrop Kit 4" for dryhopping and adding other ingredients to a pressurized fermenter without oxygen. Fits F100/F150/F200/F300 and other 4".Included in the box:- Butterfly-valve, TC 4"- TC Adapter, 4" til 34mm- TC Pipe, 4", L=200mm - Tri Clamp, 4" (2 pcs)- Tri Clamp, 34mm (3 pcs)- TC34mm Manual PRV- TC34mm Ball Lock connector, Gas- TC Tee, 34mm, L=60mm- TC Gasket, 4", (3 pcs)- TC Gasket, 34mm DN20, 5-pack

Brewtools MiniUni 40L The MiniUni™ tanks are a range of high quality, flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EUSpecification:Pack size: 34 (w) x 34(d) x 92 (h) cmWeight without packaging: 11.2 kgWeight with packaging: 12 kgTank diameter (inside): Ø28 cmMax. recommended volume: 40 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSI< strong>This comes with:MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

Brewtools MiniUni 50L The MiniUni™ tanks are a range of high quality, flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EU Specification:Pack size: 34 (w) x 34(d) x 108.5 ( h) cmWeight without packaging: 12.85 KgWeight with packaging: 14.8 KgTank diameter (inside): Ø28 cmMax. recommended volume: 10 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSIThis comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

Better Brew LCD-strip thermometer covers normal wine fermentation temperatures 14-30 degrees Celcius. This thermometer is self-adhesive so you can attach it to the outside of the fermenter for constant monitoring. Very practical thing that always sits where it should.

This LCD-strip thermometer covers normal wine fermentation temperatures 14-30 degrees Celcius. This thermometer is self-adhesive so you can attach it to the outside of the fermenter for constant monitoring. Very practical thing that always sits where it should.Bulk-pack

Better Brew Full-Range LCD Strip Thermometer covers normal wine fermentation temperatures 0-30 degrees Celcius. This thermometer is self-adhesive so you can attach it to the outside of the fermenter for constant monitoring. Very practical thing that always sits where it should.

Better Brew Glasdamejeanne 23L with thick wall. Use with 50mm rubber cap or a 35/29mm rubber/silicone plug.

Better Brew Glasdamejeanne 11L with thick wall.

Plastic Damejeanne 5L with drilled Cap and Grommet. For fermentation of beer, wine, cider, mead etc. Not suitable for hot liquids. Airlock not included.Dimensions - Height ca 33cm (excluding airlock),  Width / Depth ca 14cm

Graded and food-grade plastic can of the highest quality. Neutral translucent colour.Plastic container 5L incl. CapVolume: 5 liters with M40 white or black screw cap.Material: polyethylene (HDPE)Width: 12 cmDepth: 18 cmHeight: 30 cm

9-PACK. Graded and food-grade plastic can of the highest quality. Neutral translucent colour.Plastic container 5L incl. Cap 9-PACKVolume: 5 liters with M40 white or black screw cap.Material: polyethylene (HDPE)Width: 12 cmDepth: 18 cmHeight: 30 cm

Screw Cap for 5L plastic container 5L, white or black. Note: Container/can is not included.

Better Brew Plastic Damejeanne 27,5L

Better Brew Plastic Damejeanne 27,5L

Better Brew 16L Plastic Fermenter Complete with scale, lid and rubber grommet

Better Brew 30L Plastic Fermenter with Scale, Handle, Lid and grommet

Black Cap 50mm

Plastic Bucket 30L with no accessories (no lid, no handle etc)

Plastic Bucket with no accessories

Air lock 50 mm for 25L fermenter

Brewbelt by Better Brew EUROPEAN VERSION - EU Plug. Homebrew Heat Belt - 25W – Round 2-Pin EU Plug. Keep your yeasties snug and warm with this simple to use heat belt. This is a heating belt that goes round your bucket, keg demijohn or other fermenter to keep it warm so your yeast ferments at it's preferred temperature. Perfect if you need to keep your brew in a spare room, garage of cellar where the temperature is less than idea for brewing. Simple to adjust the temperature by changing the position of the belt. Instructions included.- Gives you a quicker, more complete fermentation. - Easy to store away after use unlike heat pads.Can be used on:- Barrels - Kegs - Carboys - Buckets - or 2 Demijohns side by side

Heat Pad by Better Brew EUROPEAN VERSION - EU Plug. Homebrew Heat Pad - 25W – Round 2-Pin EU Plug. Keep your yeasties snug and warm with this simple to use Heat Pad. Perfect for your bucket, keg, demijohn or other fermenter to keep it warm so your yeast ferments at it's preferred temperature. Perfect if you need to keep your brew in a spare room, garage of cellar where the temperature is less than idea for brewing. Instructions included.- Gives you a quicker, more complete fermentation. - Easy to store away after use unlike heat pads.Can be used on:- Barrels - Kegs - Carboys - Buckets - DemijohnsDiameter: ca 30 cmThickness: ca 5 mm

Better Brew Glass Demijohn 5L (about 1 gallon). Perfect for wine, cider, mead, kombucha and beer. Ca 32mm hole/opening for bung.Included:- 1st Better Brew Demijohn 5L- 1st Bung 29/35mm in cork with hole for air lock- 1st Bung 29/35mm in cork without hole (sealed)

Glass Damejeanne 5L with handle. Can be sealed with patent-cap/swing-top, silicone/rubber bung 26mm/32mm with 9mm hole, or rubber cap 40mm. Cap or seals not included.Note that the design and appearance may vary.

Glass Damejeanne 5L with Handle and Screw Opening. Inner diameter of opening is 26mm. Can be sealed with screw-on cap, silicone/rubber bung 23mm/29mm with 9mm hole. Screw-on cap not included.Note that the design and appearance may vary.

This RAPT wifi connected temperature controller box will enable you to monitor, track and control heating and cooling devices remotely through the internet via the Android or Iphone APP. Set complex temperature profiles so the temperature will automatically change over time. Universal thermostat. NOTE! EU-power plugs 220-240V (not as picture shows).The Google Play Android App can be downloaded via the link below.https://play.google.com/store/apps/details?id=io.raptOr search for "kegland rapt" The Apple App Store RAPT App can be downloaded via the link below.https://apps.apple.com/th/app/ rapt/id1573192994Or search for "kegland rapt""This app is a web mobile wrapper that allows you to browse the RAPT portal/website so that the website renders into a mobile device screen increasing usability on your device.  It also gives you the added functionality of push notifications to your mobile device." This temperature connects with the RAPT web portal meaning that you can monitor, log and control the devices plugged into this temperature controller box remotely.The colour screen clearly displays temperature, graph of future and past temperature settings and makes it much easier to perform profile temperature steps.This plug and play temperature controller box has two clearly marked blue and red power sockets for heating and cooling so you can control a fridge or heating device at the same time to completely monitor and control the temperature. Each power outlet is rated to 10amp (2400 Watt max).PID IncludedThis temp controller box comes with PID heating function often used for higher powered devices. This greatly reduces the chance of scorching and will deliver better temperature control with less fluctuation.Temperature RangeThe temperature range of this device will enable you to control devices from -20C and up to 120C.Various Mounting OptionsThis innovative design enables you to panel mount this controller, mount to a hanging point or hook, mount on top of a fridge or brewery. Simply unscrew the mounting plate and switch the mounting to your preferred orientation.RAPT Wifi CompatibleThis product will connect with the https://app.rapt.io/ portal.  This portal will enable you to monitor, control and log past temperature and also show a future projection of temperature profiles that you might have running.

Brewly Lid Seal for CF 30L Fermenter - Spare part

This collection container fits the FermZilla Tri-Conical fermenter with 3 Inch x 3 Inch Butterfly Valve. Incl. Tri Clover Clamp, End Cap and Seal. NOTE: Fits only Gen3 (Tri-Conical)

Brewly Racking Arm for Conical Fermenter with 2pcs silicone o-rings with 9mm outer diameter and 6mm inner diameter, thickness ca 1,5mm.

Mangrove Jack - Lid Seal for Stainless Steel FermenterSpare Part.

Conicus Pro 30L is a stainless steel conical fermenter that can handle max pressures up to 2 bars (1 bar working pressure). Made from quality stainless steel, the Conicus Pro is robust, durable, and designed to elevate your home brewing experience. With a unique 3” sight glass, allowing brewers to observe the beer, level, and fermentation process like never before.Conicus Pro by BrewolutionHomebrewing enthusiasts, meet the Conicus Pro! The essence of innovation and functionality in the world of homebrewing and stainless-steel conical fermenters or Unitanks for short. This is not just another pressurised conical fermenter; it is the realisation of every homebrewer's ultimate dream, offered at a price range accessible to all. Made from quality stainless steel, the Conicus Pro is robust, durable, and designed to elevate your home brewing experience. Conicus Pro by Brewolution.All the ports you needConicus Pro comes with all the features and ports you need. Including a 1.5” tri-clamp stainless-steel butterfly sample valve and a 2” tri-clamp stainless-steel butterfly dump valve. It has an operating pressure of 1 bar. The Conicus Pro stands as a testament to advanced fermenting technology.3-inch Sight GlassThe unique 3” sight glass is a game-changer, allowing brewers to observe the beer, level, and fermentation process like never before. Additionally, the sight glass is designed for the future with focus and features for digital hydrometers. The sight glass lets transmission from devices like the Graviator or other digital hydrometers escape, ensuring data flow and precise monitoring of your brew.CIP CleaningThe fantastic feature of the Conicus Pro is its capability for CIP (Clean-In-Place) cleaning. This method is not only easy and quick but also incredibly effective, guaranteeing comprehensive cleaning and sanitation.Temperature ControlStainless steel allows for effective temperature control. The Conicus Pro fits inside the Ferminator. With the Ferminator you can set the desired temperature and maintain this accurate temperature stable during the fermentation. It can also be easily integrated with an insulated jackets and coil chiller or other temperature control systems, providing stability during fermentation.In the box1x Conicus Pro Stainless-steel Fermenter1x 1,5” tri-clamp stainless-steel butterfly valve1x 2” tri-clamp stainless-steel butterfly valve1x 2” tri-clamp elbow 90°1x 3” Sight glass incl. 2 x gasket5x 1,5” tri-clamp blind cap1x 2” tri-clamp blind cap1x 4” tri-clamp blind cap5x 1,5” tri-clamp gasket4x 2” tri-clamp gasket1x 4” tri-clamp gasket5x 1,5” tri-clamp3x 2” tri-clamp1x 4” tri-clamp1x Airlock, 3-Piece1x Silicone Bung1x ManualSpecifications- Max volume 32 L. (Minimum Brew Size is 12-15L)- Max brew volume: 28-30* L. Read more in FAQs - Min brew volume: 12-15* L. Read more in FAQs - Working pressure 1 bar, max pressure 2 bar - Matt stainless-steel finish on the outside.- Super smooth stainless-steel finish on the inside.- Liter and US gallon scale on the inside.- 3” Sight glass with liter and US gallon scale- Stainless steel AISI 304- Lid: 1 x 4” port, 2 x 1,5” ports, 1 x 2” port- Body: 4 x 1,5” ports- 1,5” tri-clamp stainless-steel butterfly sample valve- 2” tri-clamp stainless-steel butterfly dump valve- 2 stainless steel handles- Airlock, 3-piece, and silicone bung incl.- Tree fixed legsSize & WeightHeight: 79,5 cm (87 cm with airlock)Diameter at the top: 42 cmWeight Gross: 18 kgWeight Net: 13.5 kg- See product image gallery for dimensions

Conicus Pro 55L is a stainless steel conical fermenter that can handle max pressures up to 2 bars (1 bar working pressure). Made from quality stainless steel, the Conicus Pro is robust, durable, and designed to elevate your home brewing experience. With a unique 3” sight glass, allowing brewers to observe the beer, level, and fermentation process like never before.Conicus Pro by BrewolutionHomebrewing enthusiasts, meet the Conicus Pro! The essence of innovation and functionality in the world of homebrewing and stainless-steel conical fermenters or Unitanks for short. This is not just another pressurised conical fermenter; it is the realisation of every homebrewer's ultimate dream, offered at a price range accessible to all. Made from quality stainless steel, the Conicus Pro is robust, durable, and designed to elevate your home brewing experience. Conicus Pro by Brewolution.All the ports you needConicus Pro comes with all the features and ports you need. Including a 1.5” tri-clamp stainless-steel butterfly sample valve and a 2” tri-clamp stainless-steel butterfly dump valve. It has an operating pressure of 1 bar. The Conicus Pro stands as a testament to advanced fermenting technology.3-inch Sight GlassThe unique 3” sight glass is a game-changer, allowing brewers to observe the beer, level, and fermentation process like never before. Additionally, the sight glass is designed for the future with focus and features for digital hydrometers. The sight glass lets transmission from devices like the Graviator or other digital hydrometers escape, ensuring data flow and precise monitoring of your brew.CIP CleaningThe fantastic feature of the Conicus Pro is its capability for CIP (Clean-In-Place) cleaning. This method is not only easy and quick but also incredibly effective, guaranteeing comprehensive cleaning and sanitation.Temperature ControlStainless steel allows for effective temperature control. The Conicus Pro fits inside the Ferminator. With the Ferminator you can set the desired temperature and maintain this accurate temperature stable during the fermentation. It can also be easily integrated with an insulated jackets and coil chiller or other temperature control systems, providing stability during fermentation.In the box1x Conicus Pro Stainless-steel Fermenter1x 1,5” tri-clamp stainless-steel butterfly valve1x 2” tri-clamp stainless-steel butterfly valve1x 2” tri-clamp elbow 90°1x 3” Sight glass incl. 2 x gasket5x 1,5” tri-clamp blind cap1x 2” tri-clamp blind cap1x 4” tri-clamp blind cap5x 1,5” tri-clamp gasket4x 2” tri-clamp gasket1x 4” tri-clamp gasket5x 1,5” tri-clamp3x 2” tri-clamp1x 4” tri-clamp1x Airlock, 3-Piece1x Silicone Bung1x ManualSpecifications- Max volume: 57 L.- Max brew volume: 50-55* L. - Min brew volume: 20-25* L.- Working pressure 1 bar, max pressure 2 bar - Matt stainless-steel finish on the outside.- Super smooth stainless-steel finish on the inside.- Liter and US gallon scale on the inside.- 3” Sight glass with liter and US gallon scale- Stainless steel AISI 304- Lid: 1 x 4” port, 2 x 1,5” ports, 1 x 2” port- Body: 4 x 1,5” ports- 1,5” tri-clamp stainless-steel butterfly sample valve- 2” tri-clamp stainless-steel butterfly dump valve- 2 stainless steel handles- Airlock, 3-piece, and silicone bung incl.- Tree fixed legsSize & WeightHeight: 108,5 cm (115 cm with airlock)Diameter at the top: 42 cmWeight Gross: 21,5 kgWeight Net: 16 kg- See product image gallery for dimensions

The jacket can retain the heat generated during the fermentation and improve the performance of the fermenter, even when you are fermenting in a cold room.The jacket is also a must if you have the lid with spiral cooler. The jacket can help with an even more controlled and effective temperature regulating inside the fermenter.Insulation thickness: 6 mm.Material: durable and rugged styrene butadiene rubber.

The jacket can retain the heat generated during the fermentation and improve the performance of the fermenter, even when you are fermenting in a cold room.The jacket is also a must if you have the lid with spiral cooler. The jacket can help with an even more controlled and effective temperature regulating inside the fermenter.Insulation thickness: 6 mm.Material: durable and rugged styrene butadiene rubber.

The 4” Lid with Coil Chiller is a exceptional brewing accessory designed for use with water, glycol chiller or similar systems. This tri-clamp 4” Lid with Coil Chiller will fit many fermenters e.g., Conicus Pro, Ss Brewtech, Brewtools, Brew Monk etc.  Perfect for Conicus Pro 55L. The core of this product is its stainless steel chilling coil. Immersed directly in your fermenting beer, it works efficiently to maintain ideal fermentation temperatures. The coil is crafted from high-quality stainless steel and is easy to clean, ensuring durability and reliability in your brewing process. Its length and width are thoughtfully designed to fit perfectly within the Conicus Pro 4" opening or similar systems.Installing the chilling coil is straightforward. It involves fitting the coil into the 4" opening and close it with the Tri-Clamp. For cooling, you will need an insulated tubing kit (either the one provided or your own), which connects the coil to your glycol chiller. This setup is vital for precise temperature control during fermentation, especially crucial when brewing lagers, which require colder fermenting temperatures.The 4" Lid with Coil Chiller also offers an efficient solution for cold crashing your beer. Cold crashing is a technique used to improve beer clarity and mouthfeel by bringing the beer to a low temperature, causing residual yeast and other particles to settle at the bottom of the fermenter.You can easily connect water, glycol chiller or similar systems to the inlet and outlet to the two male connections.We recomend bying the Conicus Pro 30 Insulation jacket with this Coil ChillerFeatures:521 mm long stainless-steel spiral cooler4" LidLid mounted two male connections for water or glycol chillerWith beer and Co2 postAISI 304 stainless-steelEasy to clean.Intergrated in the lid is a beer and CO2 post for carbonating and dispensing the beer. These posts are smart integral parts of the lid: one for adding gas (CO2) and the other for dispensing the liquid (beer).If you want to control the temperature during the fermentation the Conicus Pro can be mounted with this optional lid with a build-in cooling coil. This is a very simple, but effective way of controlling the temperature inside the fermenter.We recomend using the Ferminator for a more easy, effective and precise temperature regulating.This tri-clamp 4” Lid with Coil Chiller will fit many fermenters e.g., Conicus Pro, Ss Brewtech, Brewtools, Brew Monk etc.

The 4” Lid with Coil Chiller is a exceptional brewing accessory designed for use with water, glycol chiller or similar systems. This tri-clamp 4” Lid with Coil Chiller will fit many fermenters e.g., Conicus Pro, Ss Brewtech, Brewtools, Brew Monk etc. The core of this product is its stainless steel chilling coil. Immersed directly in your fermenting beer, it works efficiently to maintain ideal fermentation temperatures. The coil is crafted from high-quality stainless steel and is easy to clean, ensuring durability and reliability in your brewing process. Its length and width are thoughtfully designed to fit perfectly within the Conicus Pro 4" opening or similar systems.Installing the chilling coil is straightforward. It involves fitting the coil into the 4" opening and close it with the Tri-Clamp. For cooling, you will need an insulated tubing kit (either the one provided or your own), which connects the coil to your glycol chiller. This setup is vital for precise temperature control during fermentation, especially crucial when brewing lagers, which require colder fermenting temperatures.The 4" Lid with Coil Chiller also offers an efficient solution for cold crashing your beer. Cold crashing is a technique used to improve beer clarity and mouthfeel by bringing the beer to a low temperature, causing residual yeast and other particles to settle at the bottom of the fermenter.You can easily connect water, glycol chiller or similar systems to the inlet and outlet to the two male connections.We recomend bying the Conicus Pro 30 Insulation jacket with this Coil ChillerFeatures:338 mm long stainless-steel spiral cooler4" LidLid mounted two male connections for water or glycol chillerWith beer and Co2 postAISI 304 stainless-steelEasy to clean.Intergrated in the lid is a beer and CO2 post for carbonating and dispensing the beer. These posts are smart integral parts of the lid: one for adding gas (CO2) and the other for dispensing the liquid (beer).If you want to control the temperature during the fermentation the Conicus Pro can be mounted with this optional lid with a build-in cooling coil. This is a very simple, but effective way of controlling the temperature inside the fermenter.We recomend using the Ferminator for a more easy, effective and precise temperature regulating.This tri-clamp 4” Lid with Coil Chiller will fit many fermenters e.g., Conicus Pro, Ss Brewtech, Brewtools, Brew Monk etc.

This is a stainless-steel tri-clamp sample valve with a rotating rack arm mounted on a 3/8" tap with 13 mm barb. It is easy to mount.This valve can also be used for bottling directly from your Fermenter.This tri-clamp sample valve with racking arm will fit many fermenters e.g., Conicus, Ss Brewtech, Brewtools, Brew Monk etc.AISI 304 stainless-steel.Mounted valve for easy opening and closing.Easy to clean.Easy to mount.Tri-clamp standard.

This is a stainless-steel tri-clamp sample valve with a rotating rack arm mounted on a 3/8" tap with 13 mm barb. It is easy to mount.This valve can also be used for bottling directly from your Fermenter.This tri-clamp sample valve with racking arm will fit many fermenters e.g., Conicus, Ss Brewtech, Brewtools, Brew Monk etc.AISI 304 stainless-steel.Mounted valve for easy opening and closing.Easy to clean.Easy to mount.Tri-clamp standard.

Coobra Universal thermostat with EU-connections for cooling & heating at the same time and control both manually and via Wifi app.Perfect for home brewing, fermentation breeding, incubation, greenhouse, etc.- Intelligent digital display temperature controlled outlets- Temperature range -30 - 105 ℃- Supports both Celcius and Fahrenheit- WiFi 2.4GHz wireless connection- Mobile Smartlife APP control- Manual control or app controlled.- Double relay output: connect cooling & heating at the same time- automatic alarm for high/low temperature- temperature peak, Update once in 1s- Heating/cooling mode- temperature unit conversion- Programmable in up to 7 day intervals- compressor delay protection.- Temperature sensor with 150cm cord and suction cup for fastening.

Brewly CPF35L Chiller 5,5 meters - Cooling spiral in 304 stainless steel for Brewly CPF35L pressure fermenter. NOTE: Includes only the chiller/cooling spiral, not the other equipment in the picture.

Brewly CPF35L Chiller - Cooling spiral in 304 stainless steel for Brewly CPF35L pressure fermenter. NOTE: Includes only the chiller/cooling spiral, not the other equipment in the picture.

Food grade HDPE plastic bottle of the highest quality. Neutral, natural plastic color (slightly transparent). Including black 28mm screw cap (cap).Diameter: 82.5mmHeight: 255mmMaterial: HDPE plasticCap Dimension: 28mmVolume: 1000mlWeight: 50gStandard Color: Uncolored.Screen printing: YesVolume Gradation: No

Brewly Stainless Float With Silicone Dip Tube 80cm. Ensure that only the top layer of beer is poured from the fermenter, also fits Fermzilla perfectly. Silikcone tube measurements (dip tube):Inner diameter: 6mm (ID 0.23”)Outer diameter: 8mm (OD 0,35”) Floater diameter: 43mm

Air Lock Compact Mini 30L in transparent plastic that fits ordinary plastic fermenters as well as FermZilla and Brewly fermenters. Easy to clean. Fits 9mm holes.

Spiral fermenter air lock with red or yellow cap. 10mm diameter.

The filter prevents hop residue etc from beeing sucked up into a hose, use in kegs, fermenters etc (not with float). Made from HDPE and 304 Grade stainless steel mesh this product can be boiled or sanitized with most detergents.The float can be mounted in three different places on the filter, to determine how close to the surface you want to suck up liquid.Dimensions: 40 x 28 mm. Hose holder diameter: 8 mm, perfect for 6mm inner diameter silicone tube/hose. Materials: Stainless steel 300 mesh and plastic. NOTE: dont use with float as there are no attachments for float on the filter

Fits CO2/Beer Ball-lock-coupling. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Stainless steel.

Add this pressure kit to your FermZilla 27L, 35L or 55L and turn your FermZilla into a true uni tank that can be used for carbonating beer. Stainless steel.Brewly Stainless Pressure Kit includes:- 2 x Carbonation Screw Caps with barb- 1 x SS Float & 80cm Silicone Dip TubeThis inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:Fermenting Under Pressure:First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Pushing, and Serving:When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Lack of OxidationBecause the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:• Ferment beer under pressure to reduce ester and fusel alcohol production• Ability to always draw clear beer with the unique, floating draw tube • Keg already carbonated beer• Use co2 to push beer into a keg or though a filter into a keg• Carbonate and serve beer directly from the FermZilla, eliminating kegging all together.